Difference between revisions of "Welcome to CANNY Wiki!"

[unchecked revision]

Revision as of 12:45, 11 September 2016

CANNY's original documentation was written in Russian. You can find it here: http://wiki.canny.ru

We are intensively translating the documentation into English. You may track the work progress as displayed on the page below.

For now and always we are keen to answer any of your questions here and here.

EN = Translated.

EN = Translated but need to check.

EN CANNY Lab - Main article
EN Main window - CANNY Lab Main window, tools and menu
EN Functional Diagram Editor mode - Functional diagram editor description and basic operations
EN Simulator mode - CANNY Lab IDE simulator mode
EN Interaction with equipment - CANNY Lab IDE and controller interaction
EN Firmware Update Utility - Creating and using SFX-Files

Constants and Registers Constant Copy Input Register Output Register	Logical operators Negation Logical AND Logical OR Exclusive OR	Bitwise operators Bitwise AND Bitwise OR Bitwise exclusive OR Bitwise Inversion Left shift Right shift Left rotation Right rotation
Relational operators Equal to Greater than Not greater than Less than Not less than	Arithmetic operations Addition Subtraction Multiplication Division	Flip-flops / Latches SR latch RS latch D flip-flop T flip-flop JK flip-flop Buffer
Timers and Generators Delayed turning ON Delayed turning OFF PWM Generator RND Generator	Counters and Edge Detectors Counter Rising edge detector Falling edge detector	Converters Converter 8-to-1 Converter 16-to-1 Converter 1-to-8 Converter 1-to-16 ASCII to Integer Integer to ASCII Map
Switches Switch 2-to-1 Switch 8-to-1 Switch 16-to-1 Switch 1-to-2 Switch 1-to-8 Switch 1-to-16	Decoration Label

EN CANNY 7 - Main article
EN Programmable Logic Controller - General information about the programmable logic controllers
EN System Registers - Managing system operation and indication
EN Discrete Inputs and Outputs - Using IO channels in a discrete mode and low-resolution PWM mode (1 ms)
EN High Resolution PWM - Using IO channels #1 and #2 in high-resolution PWM mode (1 us)
EN UART / RS232 / Modbus - Using IO channels #9 and #10 in serial data interface asynchronous mode.
EN CAN Interface - Configuring and using built-in CAN-Interface
EN LIN - Using IO channels #9 and #10 in LIN MASTER or LIN SLAVE modes.
EN I²C - Configuring and using channels in MASTER mode of synchronous serial data interface I²C
EN Dallas® 1-Wire® - Configuring and using channels in MASTER mode of asynchronous serial data interface 1-Wire®
EN User pre-Programmed Parameters - Access to parameters, set by the user when loading a software to the controller with Firmware Update Utility
EN EEPROM Non-volatile Memory - Writing and reading data to/from non-volatile memory
EN Infrared Remote Control Driver - Configuring and using channels for receiving and transmitting IR remote control commands

@@ Line 112: / Line 112: @@
 * <span style="color:#fff000">'''EN'''</span> [[CANNY 7, HR PWM Driver | High Resolution PWM]] - Using IO channels #1 and #2 in high-resolution PWM mode (1 us)
 * <span style="color:#fff000">'''EN'''</span> [[CANNY 7, UART Driver | UART / RS232 / Modbus]] - Using IO channels #9 and #10 in serial data interface asynchronous mode.
-* <span style="color:#fff000">'''EN'''</span> [[CANNY 7, CAN Driver |CAN Interface]] - Configuring and using built-in CAN-Interface
+* <span style="color:#f000ff">'''EN'''</span> [[CANNY 7, CAN Driver |CAN Interface]] - Configuring and using built-in CAN-Interface
 * <span style="color:#fff000">'''EN'''</span> [[CANNY 7, LIN Driver | LIN]] - Using IO channels #9 and #10 in LIN MASTER or LIN SLAVE modes.
 * <span style="color:#fff000">'''EN'''</span> [[CANNY 7, I²C Driver | I²C]] - Configuring and using channels in MASTER mode of synchronous serial data interface I²C